It seems you are very knowlegable on the green blinking syndrome. I too am now a member of this plague. I have a Mits 52525 and replaced the 4 16v 1000uf caps with 35v 1000uf caps to no avail. I would be greatly indebted to you if I could get your documents on this issue. Hopefully it will give me some insight into other options to try. Let me know what I need to do to get this valuable information. If you can email them. please email to [email protected].
If possible, can I have the repair information e-mailed to me also to replace the bad capacitors on the Mitsubishi 62825 television. I have the GBLOD disease too.
I heard somwhere thatwhen people buy the Radio Shack capacitors as replacements for the circuit boards,they will not hold up to the high heat this television puts out. Over time, the high heat will make these capacitors fail. I heard someone recommended a certain brand name of the high heat brand capacitors that people need to use when repairing these circuit boards in this television. Have you heard what brand capacitors that people need to use on these circuit boards so they don't use the same ones that came with the television. When these circuit boards are repaired by Mitsubishi, I heard they use the old capacitors that originally came with the televisions when they were new. If you put these capacitors back on the circuit boards to repair them, you end up right back in the same boat with your circuit board on the television going bad again.
If I repair this television once, I don't want to end up going back into this thing for a while.
Hi Larry / All,
Wow. This thread is long and you've stuck with it! Congrats.
I have a WD-62825 with the green blinking light. I replaced the 4 caps on the DM and FMT boards back in May. This took care of the problem for a few months but the light is back now.
I the replaced all caps on the PWB as well as some SMT caps that tested bad with an ESR meter on the FMT. All standby supplies seem to be coming up (only a little high). No high ripple measured.
+/- 15 supply is at ~17
6 volt supply is at 7
The set will boot and fire if I disconnect the 6v supply from the DM, plug it in, wait 15 seconds, and then reapply the 6v line. STRANGE.
Any help would be appreciated (and compensated). I used to do this for a living and would like to help you out if possible.
Hi Larry its me again Aimee I own th Mitsubishi HDTV Model WS-48515. I have taken the back off my tv and wanted to know if you could tell me if you would know where the DM board would be located inside the set or if you could email me the repair manual by any chance please. Thank you very much [email protected]
Hi Larry....
Guess what? I also have the green blinking light problem with my set.
Could you please send me a copy of the repair instructions as well?
WD-52725
Thank you very much. [email protected]
Guess what CMG? It's ASSES like you that make people like Larry and I not want to help complete idiots like yourself. Have you tried to solve this problem or are you just waiting for free handouts?
If you've read this thread you'll see that Larry has severe medical issues. I / we can only hope that he is faring well.
Instead of paying $6000 for a television, you should work on your education and lessons on how to treat people.
I'm sure a doctor could prescribe a great drug or two for you as well.
Larry Dillon said: now now boys no need to throw insults but you do catch more flies with honey then you do with vinigar, CMG What is your issue with me?
You are correct. I overreacted and I apologize. I just don't like seeing innocent people treated that way.
Anyway, do you have any thoughts on my comments above? Would you mind emailing me your notes so I can see if I can learn something from your experience with this chassis?
Larry is one of the most, if not THE, most helpful and giving individuals I've ever encountered. If
you had been through what he has endured the past year, you'd see how
any derogatory comment toward him is truly in poor taste. He has
earned my, and many others who've been involved here, respect and
admiration a million times over.
You're trying to get help in an online forum, yet insulting those who have the ability to help you. Doesn't that seem a little counterintuitive? Don't you realize that the people who help others in forums like this don't get paid? They're volunteers, fellow members that donate their own time to lend a helping hand, share experiences, and give advice. It's amazing to me that there are people in this world that find reward in helping others, asking for nothing in return. And, at the same time, it sickens me that there are those like yourself, who find pleasure and reward spreading hatred and discontent.
I've already wasted enough time even acknowledging your existence with this post. I won't ban you for sharing your opinion, no matter how selfish and arrogant it may be. However, I think I speak for the entire community by saying your comment is unappreciated and your presence here no longer wanted. Please don't come back.
Hi Larry Dillon
Thank you for sending me the repair information on the Mitsubishi 62825 television.
I had a problem when I opened it, there was nothing there. It could be a problem on my end, I am not really sure.
Would it be possible to resend the repair information to me one more time.
I am sorry I have to ask again.
My e-mail is [email protected].
And yes Larry I really appreciate a person like you with your electonic skills taking your personal time to help people that are having trouble with these mitsubishi television sets.
I have a lot of respect for you in helping people when mitsubishi won't even step up to the plate and repair these televisions.
Thank you!
Hi Larry,
I got the zip file and everything came through great.
The reason I did not get the first file you sent, was because I did not have the program from Pando.com.
Thank you so much Larry!
I will let you know how I come out on the self repair.
Thank goodness for people like you that share their knowledge with other people.
Talk to you later.
I hope everything gets repaired ok.
I to requested the repair information for the WD-62825 and never received it.
That's OK I fixed my set my self and replacing the CAP's was not the fix.
I also wanted to share this possible fix with others on this web site but was meet with negetive comments.
Are goal is to be kicking back and watching this TV not working on it with a big ? mark on what we are doing will fix it.
I guess i am one of the lucky one's but only the techlore knows
Well my WD-62825 works great besides the blinking F-ing green light. I did buy a 3 year warranty and it was over 2 months ago. If I knew that the TV was going to be as big of pile of Sht, I would have bought a different brand. Waiting for Mitz to get back to me about fixing it at no charge. Good luck. Like to take my $4500.00 dollar Tv down to Irvine and throw it thru there window. JUNK.
I replaced all the recommended caps on all the boards, no more flashing green light, I now have a flashing yellow status light. Any helpful hints on this?
Larry, or Anyone that has some information. I have a WS-65813 Rear Projection Mitsubishi with the green blinking light activated after my baby nephew accidentally flipped the power off switch to my monster home theater filter. I have a great deal of experience working on computers and elctrical components, but no TV experience. I would love to knock this out myself if possible, and I also cannot tell you how thankful I will be for any service manual or info to help me get there. Thank you so very much in advance. [email protected]
Larry, would you be so kind to send me the information required to repair the blinking light issue? Thanks in advance for the help on this [email protected]
Larry
I now seem to have the dreaded Green Light problem. I don't have the money to get this repaired so I'll probably have to do the repairs myself. If you could please send me any documents or repair manuals needed to do this would be a big help. My email is [email protected]
Larry, would you be so kind to send me the information required to repair the blinking light issue? Thanks in advance for the help on this [email protected]
Well, I guess I am part of this growing community of shame with the green blinking light of death on a 3 yr old 52825. I would sure appreciate if you could email me those wonderful repair instructions! [email protected]
Larry, would you be so kind to send me the information required to repair the blinking light issue? Thanks in advance for the help on this. model ws-65615 thanks. [email protected]
Larry,
I would like he repair for the 62825 sent to me.
Thank you.
[email protected]
Larry,
It seems you are very knowlegable on the green blinking syndrome. I too am now a member of this plague. I have a Mits 52525 and replaced the 4 16v 1000uf caps with 35v 1000uf caps to no avail. I would be greatly indebted to you if I could get your documents on this issue. Hopefully it will give me some insight into other options to try. Let me know what I need to do to get this valuable information. If you can email them. please email to [email protected].
Thank you in advance,
Chris
Larry, I can't find your email anywhere...would you mind sending the instructions again for the wd-62825.
Thank you,
JJ
[email protected]
Hi Larry Dillon
If possible, can I have the repair information e-mailed to me also to replace the bad capacitors on the Mitsubishi 62825 television. I have the GBLOD disease too.
I heard somwhere thatwhen people buy the Radio Shack capacitors as replacements for the circuit boards,they will not hold up to the high heat this television puts out. Over time, the high heat will make these capacitors fail. I heard someone recommended a certain brand name of the high heat brand capacitors that people need to use when repairing these circuit boards in this television. Have you heard what brand capacitors that people need to use on these circuit boards so they don't use the same ones that came with the television. When these circuit boards are repaired by Mitsubishi, I heard they use the old capacitors that originally came with the televisions when they were new. If you put these capacitors back on the circuit boards to repair them, you end up right back in the same boat with your circuit board on the television going bad again.
If I repair this television once, I don't want to end up going back into this thing for a while.
Larry, my e-mail address is [email protected].
ThANKS.
Hi Larry / All,
Wow. This thread is long and you've stuck with it! Congrats.
I have a WD-62825 with the green blinking light. I replaced the 4 caps on the DM and FMT boards back in May. This took care of the problem for a few months but the light is back now.
I the replaced all caps on the PWB as well as some SMT caps that tested bad with an ESR meter on the FMT. All standby supplies seem to be coming up (only a little high). No high ripple measured.
+/- 15 supply is at ~17
6 volt supply is at 7
The set will boot and fire if I disconnect the 6v supply from the DM, plug it in, wait 15 seconds, and then reapply the 6v line. STRANGE.
Any help would be appreciated (and compensated). I used to do this for a living and would like to help you out if possible.
[email protected]
Travis
Hi Larry its me again Aimee I own th Mitsubishi HDTV Model WS-48515. I have taken the back off my tv and wanted to know if you could tell me if you would know where the DM board would be located inside the set or if you could email me the repair manual by any chance please. Thank you very much
[email protected]
If it's from LARRY you may never get it !!!!! But he is the EXPERT ! ?????? HAHA !!!!!!
Hi Larry....
Guess what? I also have the green blinking light problem with my set.
Could you please send me a copy of the repair instructions as well?
WD-52725
Thank you very much.
[email protected]
Guess what CMG? It's ASSES like you that make people like Larry and I not want to help complete idiots like yourself. Have you tried to solve this problem or are you just waiting for free handouts?
If you've read this thread you'll see that Larry has severe medical issues. I / we can only hope that he is faring well.
Instead of paying $6000 for a television, you should work on your education and lessons on how to treat people.
I'm sure a doctor could prescribe a great drug or two for you as well.
Cheers!
now now boys no need to throw insults but you do catch more flies with honey then you do with vinigar, CMG What is your issue with me?
You are correct. I overreacted and I apologize. I just don't like seeing innocent people treated that way.
Anyway, do you have any thoughts on my comments above? Would you mind emailing me your notes so I can see if I can learn something from your experience with this chassis?
Thanks!
[email protected]
Here's all I'm going to say...
Larry is one of the most, if not THE, most helpful and giving individuals I've ever encountered. If
you had been through what he has endured the past year, you'd see how
any derogatory comment toward him is truly in poor taste. He has
earned my, and many others who've been involved here, respect and
admiration a million times over.
You're trying to get help in an online forum, yet insulting those who have the ability to help you. Doesn't that seem a little counterintuitive? Don't you realize that the people who help others in forums like this don't get paid? They're volunteers, fellow members that donate their own time to lend a helping hand, share experiences, and give advice. It's amazing to me that there are people in this world that find reward in helping others, asking for nothing in return. And, at the same time, it sickens me that there are those like yourself, who find pleasure and reward spreading hatred and discontent.
I've already wasted enough time even acknowledging your existence with this post. I won't ban you for sharing your opinion, no matter how selfish and arrogant it may be. However, I think I speak for the entire community by saying your comment is unappreciated and your presence here no longer wanted. Please don't come back.
Aimee, That model of set does not have the same typ of DM or cap problem, as a mattr of fact I hav not sen many of this mol of set. SO SORRY!:>(
Hi Larry Dillon
Thank you for sending me the repair information on the Mitsubishi 62825 television.
I had a problem when I opened it, there was nothing there. It could be a problem on my end, I am not really sure.
Would it be possible to resend the repair information to me one more time.
I am sorry I have to ask again.
My e-mail is [email protected].
And yes Larry I really appreciate a person like you with your electonic skills taking your personal time to help people that are having trouble with these mitsubishi television sets.
I have a lot of respect for you in helping people when mitsubishi won't even step up to the plate and repair these televisions.
Thank you!
ot a problem, everything in the folder is zipped. on it's way to you, good luck!
Hi Larry,
I got the zip file and everything came through great.
The reason I did not get the first file you sent, was because I did not have the program from Pando.com.
Thank you so much Larry!
I will let you know how I come out on the self repair.
Thank goodness for people like you that share their knowledge with other people.
Talk to you later.
I hope everything gets repaired ok.
I to requested the repair information for the WD-62825 and never received it.
That's OK I fixed my set my self and replacing the CAP's was not the fix.
I also wanted to share this possible fix with others on this web site but was meet with negetive comments.
Are goal is to be kicking back and watching this TV not working on it with a big ? mark on what we are doing will fix it.
I guess i am one of the lucky one's but only the techlore knows
Well my WD-62825 works great besides the blinking F-ing green light. I did buy a 3 year warranty and it was over 2 months ago. If I knew that the TV was going to be as big of pile of Sht, I would have bought a different brand. Waiting for Mitz to get back to me about fixing it at no charge. Good luck. Like to take my $4500.00 dollar Tv down to Irvine and throw it thru there window. JUNK.
I replaced all the recommended caps on all the boards, no more flashing green light, I now have a flashing yellow status light. Any helpful hints on this?
a flashing yellow light usually means that the lamp cover is open or not slosed and locked down properly.
Larry, or Anyone that has some information. I have a WS-65813 Rear Projection Mitsubishi with the green blinking light activated after my baby nephew accidentally flipped the power off switch to my monster home theater filter. I have a great deal of experience working on computers and elctrical components, but no TV experience. I would love to knock this out myself if possible, and I also cannot tell you how thankful I will be for any service manual or info to help me get there. Thank you so very much in advance. [email protected]
Larry, would you be so kind to send me the information required to repair the blinking light issue? Thanks in advance for the help on this [email protected]
Larry
I now seem to have the dreaded Green Light problem. I don't have the money to get this repaired so I'll probably have to do the repairs myself. If you could please send me any documents or repair manuals needed to do this would be a big help. My email is [email protected]
Larry,
Sorry, but I forgot to tell you that my Green Light problem is with the Mitsubishi WD-62825.
help help help ! i have the WD-62825 and guess what a little green lite also man would love to what to change ?????
so how is the little green lite problems comming along mine just started this weekend i need help
Larry, would you be so kind to send me the information required to repair the blinking light issue? Thanks in advance for the help on this [email protected]
WD62825
hay larry can u help me i have theWD62825 and the famous blinking lite my add is [email protected]
Well, I guess I am part of this growing community of shame with the green blinking light of death on a 3 yr old 52825. I would sure appreciate if you could email me those wonderful repair instructions! [email protected]
Larry, would you be so kind to send me the information required to repair the blinking light issue? Thanks in advance for the help on this. model ws-65615 thanks. [email protected]
Pages