larry could you plese send the intructions for repairing the Dm board for the blinking green light issue on the WS-55613 to [email protected] thank you,JJ
I'm new @ this however, I can fix anything. My WD52525 (4bulbs later) is now red light contantly..I've been reading too much. Where do I start? Is it time to replace the caps? That appears to be my next step. Any manuals/downloads would be appreciated. Thanks Marc
Larry, Hey I was in luck, my 65613 was still under warranty and they came and fixed the caps 4 free. They wouldn't use the ones I bought from digikey , saying that Mitsi made them use the identical cap same as before.... OK it's free...........Now it is doing the same thing it was doing before the caps went bad. Shutting off , blinking , then I can turn it back on and it works fine for another week.......
Question is ..should I take it back apart and install the 1000/16v caps to stop this nightmare?
No let them find out why this is happening. You have a warranty and this is a problem you had before the caps went bad. Could be a problem with caps in the power supply or perhaps the Formatter board is going bad.
I have the same blinking green light. Model WS 65513 65" 4 years old. We had a power outage last night during a winter storm. Can someone send the the repair instructions? I would greatly appreciate it.
Could you also send me the repair for the dreaded blinking light for model ws65513? Also if anyone has any tips for me on soldering that would be greatly appreciated.
Larry, I now have the blinking green light (blinks three times then goes out until I press the power button again) on my WS-55805. Can you email instructions on replacing caps for this model? My email is [email protected]. I also have the service manual for this model in case I should use it to refer to the correct caps/board. Thanks!
FRoller, I am sorry but there is no DM fix or easy fix as far as I know for your TV set. If the set blinks the light for 3 seconds and goes out, It is not a DM problem, if there is even a DM in this set. It does not sound like there is. If you have the service manual, send to [email protected] and I will see if I can see a common denominator that would cause this. Good luck
Larry Dillon said: FRoller, I am sorry but there is no DM fix or easy fix as far as I know for your TV set. If the set blinks the light for 3 seconds and goes out, It is not a DM problem, if there is even a DM in this set. It does not sound like there is. If you have the service manual, send to [email protected] and I will see if I can see a common denominator that would cause this. Good luck
Larry,
Thanks for the info. The service manual I have is paper. Is there any way to decode what three blinks really means on a mitsubishi? The service manual doesn't list anything. Guess it's time to call a service person.
Larry Dillon said: I guess so man, as without a service manual, I would be stabbing in the dark. Let us know what you find out please. Good Luck
Larry,
I did some checking online and found one thread somewhere that listed error codes and how to get them to display on the timer led (just like my chevy!). I press the input and the menu buttons on the tv front panel for about 30 seconds and then the timer led flashes a code 12 (again just like my chevy). It does this 5 times.
The thread that I found this described said that code 12 means there's no error (fault).
So now I'm hunting down what code 12 really means for my set. Was it something that I did in the service mode that is keeping the set off? Are there other front panel tricks?
Error code 12 simply means that no fault is detected. When you say was it something you did in the menu? What were you setting in the menu and why were you in the menu adjusting? Also, in the menu, if you do change a setting or value, you are suppose to write down what the original setting was in case you mess up something as there is no reset for most of those settings.
I believe I hit enter on 'Initial' , I hit enter on 'E2Reset' (but not QV right after because the manual said that it would require full adjustment). I also believe I hit enter on 'DTV Diagnostics' and 'DTV E2Reset'.
I was mainly in the service mode to do the convergence there instead of the usual method using the standard menu. I also had what I believe was a 1080 input from my hdtv receiver and so I wanted to set the DTV mode to HD before doing the convergence. When I changed it to HD the screen went out of lock so I put it back to Auto mode.
After doing the above I exitted service mode. The tv said to remove power from the DTV and reapply power whenever I selected input DTV. I assume this is because I hit enter on the above menus? It indicated channel 99.9 on the display which seems like it thought I had the internal tuner.
The tv continued to work on Ant1 and I was able to enter the standard menus. I tried to change the Assign Input for DTV to be YPrPb but it would only show Off or RGB. Since I have the external receiver it is connected to the YPrPb inputs.
So the classic, enter service mode at your own risk, oops you just broke your tv happened I guess. I really messed up this time.
If you reset the E2, you reset everything. Not a great idea unless you know how to reprogram everything. If the convergence was off, you probably have bad convergence IC's. You should not have to readjust the service menu for the convergence unless you change a driver IC. If the unit drifts on the convergence, use the customer convergence alignment. It is to adjust only slight drifting on the convergence. Anything major will require the set to be repaired first. You made a mistake a lot of people make. The service menu is not the TV Set's fix all thing.
I Have Mitsubishi TV WD-62825 and i have a green blinking lingt on, a tech told me that the power supply is no good.
Were can i get one ? were can i get it repair?
I olso have a WD-52825 but this one don't have the blinking ligh, the tech told me that the engine light is broken and it will cost $ 600.00 to fix, any help from you it will help me a lot
I am also having problems with the timer blinking and the TV not turning on. My model # is WS-55859. Would you please send the instructions to [email protected].
Larry, can you please send me instructions on how to fix my WS-55613, it also has the green light blinking. I have read about the capacitors that go bad but I need a little help on knowing which ones and how to disassemble the [email protected]
I will have the repair information to you ASAP. Good luck
larry could you plese send the intructions for repairing the Dm board for the blinking green light issue on the WS-55613 to [email protected] thank you,JJ
I'm new @ this however, I can fix anything. My WD52525 (4bulbs later) is now red light contantly..I've been reading too much. Where do I start? Is it time to replace the caps? That appears to be my next step. Any manuals/downloads would be appreciated. Thanks Marc
Larry is a genius! 1.5 hours and $25 later my TV is pefect. Thanks so much Larry.
Jeff
[email protected]
Great news molar! Glad to hear you repaired your TV set.
Larry, Hey I was in luck, my 65613 was still under warranty and they came and fixed the caps 4 free. They wouldn't use the ones I bought from digikey , saying that Mitsi made them use the identical cap same as before.... OK it's free...........Now it is doing the same thing it was doing before the caps went bad. Shutting off , blinking , then I can turn it back on and it works fine for another week.......
Question is ..should I take it back apart and install the 1000/16v caps to stop this nightmare?
Seahawk 13902
No let them find out why this is happening. You have a warranty and this is a problem you had before the caps went bad. Could be a problem with caps in the power supply or perhaps the Formatter board is going bad.
Larry,
Can you also send me the instructions on how to take care of this blinking green light problem. I have the WS-48513 model. email = [email protected]
Thanks..
I have the same blinking green light. Model WS 65513 65" 4 years old. We had a power outage last night during a winter storm. Can someone send the the repair instructions? I would greatly appreciate it.
Email: [email protected]
Hi Larry,
Would you please send me the repair instructions for a blinking power light. Model WS-55511.
[email protected]
Regards.
David
David, on their way man. Good luck with the repair.
Larry
Could you also send me the repair for the dreaded blinking light for model ws65513? Also if anyone has any tips for me on soldering that would be greatly appreciated.
thanks,
[email protected]
Larry, I now have the blinking green light (blinks three times then goes out until I press the power button again) on my WS-55805. Can you email instructions on replacing caps for this model? My email is [email protected]. I also have the service manual for this model in case I should use it to refer to the correct caps/board. Thanks!
FRoller, I am sorry but there is no DM fix or easy fix as far as I know for your TV set. If the set blinks the light for 3 seconds and goes out, It is not a DM problem, if there is even a DM in this set. It does not sound like there is. If you have the service manual, send to [email protected] and I will see if I can see a common denominator that would cause this. Good luck
darter2, I will send out the repair instructions to you shortly. Good luck
Larry,
Thanks for the info. The service manual I have is paper. Is there any way to decode what three blinks really means on a mitsubishi? The service manual doesn't list anything. Guess it's time to call a service person.
Frank
I guess so man, as without a service manual, I would be stabbing in the dark. Let us know what you find out please. Good Luck
Larry,
I did some checking online and found one thread somewhere that listed error codes and how to get them to display on the timer led (just like my chevy!). I press the input and the menu buttons on the tv front panel for about 30 seconds and then the timer led flashes a code 12 (again just like my chevy). It does this 5 times.
The thread that I found this described said that code 12 means there's no error (fault).
So now I'm hunting down what code 12 really means for my set. Was it something that I did in the service mode that is keeping the set off? Are there other front panel tricks?
Thanks always for your help.
Error code 12 simply means that no fault is detected. When you say was it something you did in the menu? What were you setting in the menu and why were you in the menu adjusting? Also, in the menu, if you do change a setting or value, you are suppose to write down what the original setting was in case you mess up something as there is no reset for most of those settings.
Larry,
I believe I hit enter on 'Initial' , I hit enter on 'E2Reset' (but not QV right after because the manual said that it would require full adjustment). I also believe I hit enter on 'DTV Diagnostics' and 'DTV E2Reset'.
I was mainly in the service mode to do the convergence there instead of the usual method using the standard menu. I also had what I believe was a 1080 input from my hdtv receiver and so I wanted to set the DTV mode to HD before doing the convergence. When I changed it to HD the screen went out of lock so I put it back to Auto mode.
After doing the above I exitted service mode. The tv said to remove power from the DTV and reapply power whenever I selected input DTV. I assume this is because I hit enter on the above menus? It indicated channel 99.9 on the display which seems like it thought I had the internal tuner.
The tv continued to work on Ant1 and I was able to enter the standard menus. I tried to change the Assign Input for DTV to be YPrPb but it would only show Off or RGB. Since I have the external receiver it is connected to the YPrPb inputs.
So the classic, enter service mode at your own risk, oops you just broke your tv happened I guess. I really messed up this time.
Anyone need parts?
If you reset the E2, you reset everything. Not a great idea unless you know how to reprogram everything. If the convergence was off, you probably have bad convergence IC's. You should not have to readjust the service menu for the convergence unless you change a driver IC. If the unit drifts on the convergence, use the customer convergence alignment. It is to adjust only slight drifting on the convergence. Anything major will require the set to be repaired first. You made a mistake a lot of people make. The service menu is not the TV Set's fix all thing.
Hy Larry
I Have Mitsubishi TV WD-62825 and i have a green blinking lingt on, a tech told me that the power supply is no good.
Were can i get one ? were can i get it repair?
I olso have a WD-52825 but this one don't have the blinking ligh, the tech told me that the engine light is broken and it will cost $ 600.00 to fix, any help from you it will help me a lot
Thank you and looking foward to hear from you.
Larry,
I am also having problems with the timer blinking and the TV not turning on. My model # is WS-55859. Would you please send the instructions to [email protected].
Thanks,
Scott
Tony I need an e-mail address. and Scott, I will have the repair package out to you shortly. Good luck with your TV sets.
Hi,
Can you send me the instructions for the blinking light problem on Mitsubishi ws-55859.
Thanks
[email protected]
I will have them sent outy in a short time. Good luck
Larry, can you please send me instructions on how to fix my WS-55613, it also has the green light blinking. I have read about the capacitors that go bad but I need a little help on knowing which ones and how to disassemble the [email protected]
thanks
Larry,
Can you send me the instructions for the blinking light problem on the Mitsubishi WS-55513. My email is [email protected]
Thanks
Will be out to you shortly Raines. Good Luck
Hi Larry,
I have a WD-62825 and I just got the blinking green Timer light. Can you please send instructions on repair to [email protected]. Thanks for the help.
Jake
Pages