Good Luck Phil. Before you plug in the set after you repair the DM, triple check that the DM is replugged back into the main board on the bottom. It may look like it is but I cannot count how many peeps have found out the board was not in the sockets all the way and they had the same blinking light after they repaired the DM.
Sorry Rob, I cannot help you with that model number. I do not have it. Have you tried at servicemanuals.net for the manual? If you get that and send a copy to me, I will see if I can assist you or not.
hi its robi had a few numbers mixed up , can u see if u have one for wt-42311, and i will check for that model at the website u gave thank u for looking
Pls send info on cap replacement. I have a Toshiba 65H82. I suspect the DM board and intend to use the same technique as on the Mitsu units unless you have a more detailed set of instructions on my particular model. I wouldn't be surprised if the modules are identical between the various manufacturers. Here's my email addy: [email protected]
aero said: Larry I AM HAVING THE SAME PROBLEM WITH MY MITSUBISHI WS65513 WITH THE GREEN BLINKING LIGHT, CAN YO SEND ME THE INFO TO FIX THIS PROBLEM, TV IS 4 YEARS OLD. THANKS AERO
If you want the ingo you need to supply your email address to receive the info.
aero said: Larry I AM HAVING THE SAME PROBLEM WITH MY MITSUBISHI WS65513 WITH THE GREEN BLINKING LIGHT, CAN YO SEND ME THE INFO TO FIX THIS PROBLEM, TV IS 4 YEARS OLD. THANKS AERO
If you want the ingo you need to supply your email address to receive the info. JWA
JWA
MY E-MAIL ADDRESS IS [email protected] ref to WS65513 GREEN LIGHT BLINKING PROBLEM
Just a quick note to say thank you for your instruction. I went to radio shack and purchased 4 ea 35 vdc 1000 mu caps and soldered them to the DM board. The only thing I had some troubles with was the reassembly. I didn't get the DM board connected properly because it didn't get slid into the slot correctly. I took the board out of the metal case, installed the board than installed the case over the board after I knew the board was installed correctly. It powered up just fine and watched it for about the next 6 hours. I consider it fixed.
Also, the caps I purchased from Radio Shack fit under the metal cover - just barely, but they did fit. I got the caps as close to the board as possible.
Thanks again for the information and helping me save about $750.
Tad1299 said: Larry, Just a quick note to say thank you for your instruction. I went to radio shack and purchased 4 ea 35 vdc 1000 mu caps and soldered them to the DM board. The only thing I had some troubles with was the reassembly. I didn't get the DM board connected properly because it didn't get slid into the slot correctly. I took the board out of the metal case, installed the board than installed the case over the board after I knew the board was installed correctly. It powered up just fine and watched it for about the next 6 hours. I consider it fixed. Also, the caps I purchased from Radio Shack fit under the metal cover - just barely, but they did fit. I got the caps as close to the board as possible. Thanks again for the information and helping me save about $750. Tad
Tad,
What was the part nuber of the radio shcak caps you purchased? and what tv model did you use them for?
Larry, i am having the same issue as everyone else, blinking green light. i have a ws-55813 diamond. could you please send the repair instructions to [email protected] thank you very much.
Larry Dillon said: No it would not hurt what so ever, but will they fit inside the Assembly? Are they Hi temp Caps This is why I recommend the HI temp caps. If you really wanna go cheap this could certainly burn out this DIGITAL board. you have to understand. This is not a simple repair. This is a sophisticated board that cost almost a grand! Please follow the directions and do not go cheap. Find the right capacitors or you will not achieve what you are trying to accomplish. I am simply trying to help out folks, but when they try to defeat my directions, I have to throw up my hands. I truly hope you find the right parts and do not try and use cheap parts! Good Luck
Larry I am here for the dreaded mitsubishi blinking light on the 48" model wondering if you could send me the goods at [email protected]
Donovan, if it is for the same model number of this thread, sure, I can certainly help you out. I will send out the info in just a little bit. Good Luck with the repair.
I too am having the same green blinking light problem with the WS-65813 from Mitsubishi. Could someone forward me the repair instructions, [email protected]?
Do you have documentation on the the WD52825 for the Blinking Green Timer light. I am having trouble getting a repair person out to look at my unit as I live to far out of their service areas. [email protected]
I soldered the caps in this evening and it works perfectly once again! (WS-55813) Thanks so much! I saved hundreds with your advice. In fact it cost me $23.78 with the de-soldering tool. :)
Good Luck Phil. Before you plug in the set after you repair the DM, triple check that the DM is replugged back into the main board on the bottom. It may look like it is but I cannot count how many peeps have found out the board was not in the sockets all the way and they had the same blinking light after they repaired the DM.
Sorry Rob, I cannot help you with that model number. I do not have it. Have you tried at servicemanuals.net for the manual? If you get that and send a copy to me, I will see if I can assist you or not.
hey larry
hi its robi had a few numbers mixed up , can u see if u have one for wt-42311, and i will check for that model at the website u gave thank u for looking
rob
I do not have a number like that as well. Double check the model number please.
Larry,
Pls send info on cap replacement. I have a Toshiba 65H82. I suspect the DM board and intend to use the same technique as on the Mitsu units unless you have a more detailed set of instructions on my particular model. I wouldn't be surprised if the modules are identical between the various manufacturers. Here's my email addy: [email protected]
Thanks!
Would someone please send me a copy of how to stop the blinking green light problem. I have the Mitsubishi WD-52825. Thank you
Larry
I AM HAVING THE SAME PROBLEM WITH MY MITSUBISHI WS65513 WITH THE GREEN BLINKING LIGHT, CAN YO SEND ME THE INFO TO FIX THIS PROBLEM, TV IS 4 YEARS OLD.
THANKS
AERO
If you want the ingo you need to supply your email address to receive the info.
JWA
JWA
MY E-MAIL ADDRESS IS [email protected] ref to WS65513 GREEN LIGHT BLINKING PROBLEM
THANKS
KEN
Ok I just emailed it to you. I have the same TV
Larry,
Just a quick note to say thank you for your instruction. I went to radio shack and purchased 4 ea 35 vdc 1000 mu caps and soldered them to the DM board. The only thing I had some troubles with was the reassembly. I didn't get the DM board connected properly because it didn't get slid into the slot correctly. I took the board out of the metal case, installed the board than installed the case over the board after I knew the board was installed correctly. It powered up just fine and watched it for about the next 6 hours. I consider it fixed.
Also, the caps I purchased from Radio Shack fit under the metal cover - just barely, but they did fit. I got the caps as close to the board as possible.
Thanks again for the information and helping me save about $750.
Tad
Tad,
What was the part nuber of the radio shcak caps you purchased? and what tv model did you use them for?
thanks,
Phil
Larry, I too am having the same issue with the dreaded blinking green light. Can you send repair instructions? [email protected]
Thanks.
Modfixer, sorry, different sets totally man. If you want help on this model, please post under a different thread.
Palmer, I am mailing those out this evening to you.
Tad, geat news man! Glad to hear you got your set working. Happy New Year!
Larry,
Please send info on stopping the Blinking green light to [email protected]. I have the Mitsubishi WD-52825. Thank you
Larry, i am having the same issue as everyone else, blinking green light. i have a ws-55813 diamond. could you please send the repair instructions to [email protected] thank you very much.
brian
Runsuebee and Brian, I will have that information out to you in just a little bit. Good Luck with your repairs.
Larry I am here for the dreaded mitsubishi blinking light on the 48" model wondering if you could send me the goods at [email protected]
Donovan, if it is for the same model number of this thread, sure, I can certainly help you out. I will send out the info in just a little bit. Good Luck with the repair.
I too am having the same green blinking light problem with the WS-65813 from Mitsubishi. Could someone forward me the repair instructions, [email protected]?
I will have them out to you real soon. Good Luck with the repair.
Yeah, we have the issue too on the WS-73513. Any chance we could get the documentation? It'd be much appreciated !!!
Thanks,
[email protected] -or- [email protected]
Sure, not a problem at all. Godluck with the repairs. Just to be safe, the documents will go out to both e-mails.
Larry,
Do you have documentation on the the WD52825 for the Blinking Green Timer light. I am having trouble getting a repair person out to look at my unit as I live to far out of their service areas. [email protected]
Thank you -Suellen
Larry,
I soldered the caps in this evening and it works perfectly once again! (WS-55813) Thanks so much! I saved hundreds with your advice. In fact it cost me $23.78 with the de-soldering tool. :)
Best Regards!
Phil
Larry,
I have the same blinking green light on a 65" medallion big screen. Could you please send me the fix. My email is [email protected] thanks
brian
Brian, what is the model number of your TV set?
Larry,
My model # is ws-65613. My e mail is [email protected] Sorry about confusion thanks again for help.
Brian
Pages