Understanding Sony Television Blinking Codes

Many of the later model Sony TV’s have a built in self-diagnosis function. If the timer/standby indicator is blinking, this could be an indication of a problem with the unit. The diagnostic blinking will occur automatically with no action required by you to engage it.

The timing of the blinking you see would be as follows: two to nine blinks, (depending on the fault), about a third of a second apart, then a pause for 3 seconds, then the two to nine blinks about a third of a second apart again.

Here is a list of the problems that might have occurred indicated by the number of blinks. The words in parentheses are those, which you will see for each of these faults on a diagnosis screen described later in this article.

  • Unit is dead, No blinks - Problem in the standby power section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should show open).
  • Continuous blink once a second, no pausing - No reply from the jungle IC301 (data bus is busy, shorted to ground, or held high), IK video path is defective.
  • One blink - not used for the self-diagnosis
  • Two blinks - B+ over current protection (OCP), unit goes to the standby mode then displays the 2 blink fault. Could be a short in the power supply of any of the circuits.
  • Three blinks - B+ over voltage protection (OVP), unit goes to the standby mode then displays the 3 blink fault. This is also a problem in the power supply circuit, check T603 and R672.
  • Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505
  • Five blinks - AKB circuit (automatic kine bias), the timer/standby indicator blinks for about 30 seconds then goes to the self-diagnosis function. Something is wrong with the video. Check video out, Q705, 732, 761 and other components on the C board, also check Q218, 219, 220 on the A board. In addition, unit could be in IK blanking, try turning up screen slightly.
  • Six blinks - No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206.
  • Seven blinks - High voltage shutdown. The high voltage has exceeded 33k and the unit goes immediately into safety shutdown. Check power supply regulation and horizontal circuits.
  • Eight blinks - Problem with the audio (AUDIO), unit goes to standby and blinks the self-diagnosis code. Check IC406 audio amp, PS401, and 402. On some projection models of Sony TV sets, this code means that T8005 (flyback transformer), or the associative components in the high voltage circuits are defective on the D board.

  • Nine blinks - Replace D 6116 and D 6301 on the "G" board, do not resolder as this will fix the problem temporary. Or Panel Module Error or Thermal Error. If it is intermittent 9 blinks, meaning sometimes the TV comes on and other times you get flashing, then change the switching regulator on the "G" board or check connections. Make sure the regulator is -12 or -13 (negitive).
  • Ten blinks - Check Q8014 and Q8013 for shorts, leakage, or bad solder connections on the " D" board. If the transistors are bad, check R8051 and IC8005, also on the "D" board.

Intermittent problems? This is a great feature. You can also bring up these fault codes on-screen to see a list of the problem numbers with the abbreviation of the problem and the number of times this problem has occurred. This is slightly different than entering the service mode. To see the diagnostic screen, press the following buttons: Display, Channel, 5, volume Minus, ( not plus ) then Power. This brings up a screen with a list of the problems and number of times they have occurred. Each of the problems named, are abbreviated as, "OCP", "OVP", "V STOP", ETC. We have repeated them in parentheses in the text for the "Blinks" described above so you can correlate between the diagnostic screen and the blink codes.

Now that you know about these self-diagnostics, how do you use them? Say that you have a set with a black screen. You see that the LED is blinking four times. This would tell you that you have no vertical sweep, which is why the video is muted. If it was blinking 6 times, you would know that you have a horizontal fault. It's not a sure cure..

IMPORTANT: After you repair the unit, you MUST clear the values on this diagnostic screen. These codes do not reset themselves after the fault is corrected, so if you don't clear them, you'll be seeing "old" fault codes the next time you enter this screen. Clearing is done by going into the service mode (display, channel, 5, volume plus, then power ). Press 8 and Enter, which returns everything to the factory preset condition.

Comments

OK ThanX, this is the right forum, from the starting post it says

"Ten blinks - Check Q8014 and Q8013 for shorts, leakage, or bad solder connections on the " D" board. If the transistors are bad, check R8051 and IC8005, also on the "D" board"

If some one can verify that this has worked for them and any hints/tips they came across, I will order the bits and have a go...

hi, I have a sony trinitron, model KV24LS35U. was working fine but now stanndby light blinks 11 times. Is it worth getting fixed or scrap it? many thanks Dan

I have a Sony KDF-55xs955 rear projection LCD purchased in Nov. 2006 that will not power on and the green LED is blinking 6 times.  We had a service technician come out to take a look and immediately said the issue was a $450 power supply without even touching the TV.  I have now looked at a couple of forums that say 6 blinks = No Horizontal (H STOP), no raster, which doesn't sound much like a power supply to me.  Is the tech trying to rip me off?  Is there a way to know what it should cost me?

hey i was reading this blog and i was trying to see who cld help me...my tv is blinking 7xs and now im stuck...idk what to do so if anyone can help i wld really appreciate that thanks :0)

my tv is blinking 7xs and idk where to go from here so if someone cld help me i wld appreciate that

i have a sony trinitron model kV28HX1SU and we have no picture or sound and the stand by button is blinking permanently.

I have a 54 inch Sony Wega that turns on for a while then it will lose picture and sound both. It will stay off for about 45 seconds and come back on and play for a while and repeat this again and again. What is this problem and estimate for repairs? TV is 3 years old.

My Sony Trinitron, FD Trinitron Vega Chassis #DA4, Serial #KV32HS510 worked great yesterday, beautiful picture, is not turning on today. For a few days I had to try the power button 2 or 3 times, but it did come on. Now I get 6 blinks. If I do take it to a repair shop, what are the chances of them fixing it? I do have a friend who may be able to check it out too. What are my chances? The TV is no more that 4 or 5 years old.

Thanks!

Selita

I have a REALLY old Sony KV-1926R television.The screen is all grey snow with the numbers "7+8" in corner. unable to change voulume or channels.

HA32 said: Hi my tv it have code 10 Blinking. Audio is normal but No picture, I want to Know what the problems of it My TV Model:KP-FX432. How it can Repair? Thank you

WERE U ABLE TO FIX THE TV, I HAVE SAME TV WITH SAME PROBLEM.

CAN U PLS HELP ME?

ARINC429@HOTMAIL.COM

My sony wega tv was plug in a air condition socket, it blinks green and pause
then blinks red,4 green 6 red what could it be.

My sony wega blinks 4 green 6 red what could it be, does not turn on..

I have a sony model number kp-57ws520 that wont come on and it blinks 6 time and then starts the cycle all over again. I was told that it could be a lamp fuse problem. please help me (hawaii) is it just taht and I just need to buy a new lamp fuse?
Tony

Can anyone tell me what I am supposed to do when it doesn't turn on and when the standby light doesn't blink at all?

I have a Sony KDF-42WE655 that is producing blinking code 5. I follow the thread for reading the detailed error codes and putting it in service mode but I don't get the result i think is expected. When I use Display, 5, - volume, On button for screen test or Display, 5, + volume, On button to put it in service mode I still get no display. Is there another way to interrogate the error conditions with error code 5 when the display still does not work? What would you suggest is a best next step?

Thanks

Hi, My Sony Wega KV-HX32 started blinking red 10 times after my son & wife pressed the power on button at the same time 2 different remotes.
I get sound and no picture for 5 seconds before it powers off. Since it has no screen, I can't get into diag mode. This TV weighs 75kg so I won't be taking it to a shop. Do they cost heaps to fix. Been a good tv, only about 4-5 years old. I expect a better life for such an expensive TV.

Reply for 10 Blinks, HV PORT
I have not seen the wiring diagram of your TV KV-HX32, But in my case It was IC8002, It is a driver/Oscillator Ic. Sony asked 300 dollars to fix my projection TV kp-fx432M91.I decided to fix it myself on throw away basis, could not get much help for 10 blinks from Net.However, this post gave me lot of hope and initative. Bought Service Manual from net then few parts and finally above mentioned IC fixed the problem. Pls look for IC Part No. MCZ3001DB in D board, You will find two IC of same part number but look for the IC driving Two FETs of High Voltage Power supply section.
In most wiring diagram of Sony TV High Voltage Power Supply section components starts with 80--. as Q8013, Q8014, R8051 and IC 8002 are the essential components for HV section and these must be checked/replaced.
These all components cost only 12 Dollars in Middle East and 30 Dollars in USA and Sony may ask u minimum 250 dollars to fix 10 blinking problem. Pls do one thing search Service manual of your TV on net and route the link to me.
Thanks Techlore.

arinc429@haotmail.com

raystud said: My sony wega tv was plug in a air condition socket, it blinks green and pause then blinks red,4 green 6 red what could it be.

I have a sony trinitron model kv-32hs510 with 7 blinks. after 7 blinks, it stops for 4 seconds and repeats the blinks. i turned it off about a couple months ago and it won't turn on again. i tried unplugging it 60 seconds, overnight etc, it doesn't work. it happened once before but picture/sound came back after a week by itself. this time it's been over 2 months and we're still waiting:)...is there a way to fix it ourselves?

Was an answer ever found to Confused in Sac's issue - we are having the EXACT same problem and I can't seem to find a local SONY authorized rep. Would like info if it's available.
October 13, 2008 7:39 PM

We have a sony kdf-55xs955, rear projection LCD TV.

When I turn on the TV the picture comes on for about 30sec. to 1 min. then the picture goes off and the standby light(green) flashes continuously for approx. 30sec and then the pictures comes back for 30sec. to 1 min. and the pattern starts over. thanks for any help available.

My sony wega KV-HR36,When I turn the TV on,I only can hear the audio no picture and the green light blinks 10 times. After that The TV turn of automaticly and the red light blinks for 10 times over and over. What should I do? Anybody can help me please? Is it true that it'll cost $300 to repair it?

I have a Sony KDS-R60XBR2 sony rear projection TV
The TV does not turn on the power light goes from green to red and flashes 6 times. What would be the steps in repairing this problem?
Any help would be appercaited.
Thank you

You Have a bad lamp driver board or a bad lamp

LARRY DILLON , I HAVE A 2002 SONY KP43HT20
JUST LOST CONGERGANCE TO DAY , FLASH FOCUS WILL NOT RESET. I READ YOUR POST AND FEEL IT COULD BE THE I/C'S AND PICO FUSES. I NEVER HAD ANY REAL LUCK DESODERING PARTS OF I/C BOARD AND THINK I MIGHT BE BETTER REPLACING THE WHOLE RA-6 BOARD. WHERE WOULD BE A GOOD BUY FOR THAT AND CAN YOU E-MAIL ME THE SERVICE MANUAL???
OR MAY BE I CAN SEND THE BOARD OUT TO BE REPAIRED/ KNOW ANY ONE??

THANKS A LOT FAST DAN / E-MAIL DVHI1894@AOL.COM

first off there is NO NEED to SHOUT!! Contact PTSCORP.com cALL THEM an see how much they charge for reworking your board.

I have a 2003 sony KV32HS510 and one day the tv just went out and started blinking 6 times. A couple days later I plugged it back in and it started working again, today it went out again and it's blinking 6 times. anyone have a solution that will keep my tv on for good?

SELITA said: My Sony Trinitron, FD Trinitron Vega Chassis #DA4, Serial #KV32HS510 worked great yesterday, beautiful picture, is not turning on today. For a few days I had to try the power button 2 or 3 times, but it did come on. Now I get 6 blinks. If I do take it to a repair shop, what are the chances of them fixing it? I do have a friend who may be able to check it out too. What are my chances? The TV is no more that 4 or 5 years old. Thanks! Selita

selita I am having the exact same problem you had did you fix it and if so how?

another hero said:

SELITA said: My Sony Trinitron, FD Trinitron Vega Chassis #DA4, Serial #KV32HS510 worked great yesterday, beautiful picture, is not turning on today. For a few days I had to try the power button 2 or 3 times, but it did come on. Now I get 6 blinks. If I do take it to a repair shop, what are the chances of them fixing it? I do have a friend who may be able to check it out too. What are my chances? The TV is no more that 4 or 5 years old. Thanks! Selita

 

selita I am having the exact same problem you had did you fix it and if so how?

No, it is not fixed, yet anyway.   I have been jumping thru hoops to try to get my hands on the schematics for this TV without paying too much.  I thought Agoroquest could help with that, but so far, I cannot find them.  I will l post if it ever gets fixed.  Please do the same.  Thanx.

Does anyone know how I can get these schematics??

My tv is Red 10 blinking, with audio but no picture. On the random occasion i might get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out from behind, and i know noting. Its a Sony
KP-FX423M91. i have also pulled a wire out and put it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows or something. Can you help a person in distress??

Rags said: My tv is Red 10 blinking, with audio but no picture. On the random occasion i might get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out from behind, and i know noting. Its a Sony KP-FX423M91. i have also pulled a wire out and put it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows or something. Can you help a person in distress??

PLS GET SOME HELP FROM SOME ONE WHO CAN AT LEAST SOLDER AN IC.IF YOUR TV IS STILL ON 10 BLINKS AND SOME TIME U HAVE VIDEO ALSO ESPECIALLY U KEEP THE TV OFF FOR MORE THAN 10 HOURS.REPLACE THE IC 8002,  IC Part No. MCZ3001DB in D BOARD. IN YOUR TV D BOARD IS ON YOUR LEFT WHILE LOOKING FWD FROM BACK OF TV.BUT DO CARE ABOUT RED, HV THICK WIRE. DONOT REMOVE IT FROM BOARD SIDE, U CAN REMOVE F RED WIRE FROM D BOARD SIDE. I REPEAT GET SOME HELP AND ASK HIM TO REPLACE ABOVE MENTIONED IC. ITS PRICE IS 11 US DOLLARS.BY THE WAY WHAT IS YR LOCATION ,

ARINC429

 

Rags said:
My tv is Red 10 blinking, with audio but no picture. On the random occasion i might get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out from behind, and i know noting. Its a Sony
KP-FX423M91. i have also pulled a wire out and put it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows or something. Can you help a person in distress??

Hi Rags,

I had same problem my TV. Replaced IC8002 on the 'D' board.

This is what we did:

1.Bought 2 x MCZ3001D from WES components in Ashfield Sydney Australia for $11.20 (each).

2.Friend had an 18 pin machine spun socket (not the crappy ones on EBAY).

3.Took back off TV

4.Put the 'D' board in service position

5.Noted which way IC8002 chip sat (Where position 1 is), also noted which 2 legs are not soldered.

6.Cut the black plastic that was covering this chip underneath
(where D board screws into) as this is easier than removing the 'D'
board.

7.De-soldered the IC8002 chip with a proper de-soldering iron. These are expensive though.

8.Soldered in the 18 pin socket.

9. Set the chip into the socket.

10.Tested TV, worked fine.

11. Put it all back together, plugged in Tivo, DVD etc etc etc and all bloody good stuff.

12. I now also have a spare MCZ3001D which is taped to the back of
the TV for future replacement, which is now easier since its now in a
socket. 

smart thinking! Most of the time when I replace an IC on A printed circuit boaed I ussally install an socket as if the ICfails or needs replacement in the future it is hard on the delicate printed vcircuit landindinds as it is very easy to overheat them and then they will tear off very easy then you have a verydifficult time repairing the circuit board with hard wiring.

arinc429 said:

Rags said: My tv is Red 10 blinking, with audio but no picture. On the random occasion i might get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out from behind, and i know noting. Its a Sony KP-FX423M91. i have also pulled a wire out and put it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows or something. Can you help a person in distress??

PLS GET SOME HELP FROM SOME ONE WHO CAN AT LEAST SOLDER AN IC.IF YOUR TV IS STILL ON 10 BLINKS AND SOME TIME U HAVE VIDEO ALSO ESPECIALLY U KEEP THE TV OFF FOR MORE THAN 10 HOURS.REPLACE THE IC 8002,  IC Part No. MCZ3001DB in D BOARD. IN YOUR TV D BOARD IS ON YOUR LEFT WHILE LOOKING FWD FROM BACK OF TV.BUT DO CARE ABOUT RED, HV THICK WIRE. DONOT REMOVE IT FROM BOARD SIDE, U CAN REMOVE F RED WIRE FROM D BOARD SIDE. I REPEAT GET SOME HELP AND ASK HIM TO REPLACE ABOVE MENTIONED IC. ITS PRICE IS 11 US DOLLARS.BY THE WAY WHAT IS YR LOCATION , ARINC429

Thanks for your advise.  Im based in london.  Do you anywhere i can get pics from of the board parts ect??

Oranom said:

Rags said: My tv is Red 10 blinking, with audio but no picture. On the random occasion i might get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out from behind, and i know noting. Its a Sony KP-FX423M91. i have also pulled a wire out and put it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows or something. Can you help a person in distress??

Hi Rags, I had same problem my TV. Replaced IC8002 on the 'D' board. This is what we did: 1.Bought 2 x MCZ3001D from WES components in Ashfield Sydney Australia for $11.20 (each). 2.Friend had an 18 pin machine spun socket (not the crappy ones on EBAY). 3.Took back off TV 4.Put the 'D' board in service position 5.Noted which way IC8002 chip sat (Where position 1 is), also noted which 2 legs are not soldered. 6.Cut the black plastic that was covering this chip underneath (where D board screws into) as this is easier than removing the 'D' board. 7.De-soldered the IC8002 chip with a proper de-soldering iron. These are expensive though. 8.Soldered in the 18 pin socket. 9. Set the chip into the socket. 10.Tested TV, worked fine. 11. Put it all back together, plugged in Tivo, DVD etc etc etc and all bloody good stuff. 12. I now also have a spare MCZ3001D which is taped to the back of the TV for future replacement, which is now easier since its now in a socket. 

Hey Oranom,

Thanks for the advise and great instructions.  it looks complex, therefore i will have to hire pro help.  Someone came, took a look and said the transformer, which would cost £250GBP.  i can get a new samsung for £500, 40".  all this 18 pin socket is confussing.  got any pics.  How much do you think a pro should charge?? and how long a job??

 thanking u in advance

Rags said:

arinc429 said:

Rags said: My tv is Red 10 blinking, with audio but no picture. On the random occasion i might get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out from behind, and i know noting. Its a Sony KP-FX423M91. i have also pulled a wire out and put it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows or something. Can you help a person in distress??

PLS GET SOME HELP FROM SOME ONE WHO CAN AT LEAST SOLDER AN IC.IF YOUR TV IS STILL ON 10 BLINKS AND SOME TIME U HAVE VIDEO ALSO ESPECIALLY U KEEP THE TV OFF FOR MORE THAN 10 HOURS.REPLACE THE IC 8002,  IC Part No. MCZ3001DB in D BOARD. IN YOUR TV D BOARD IS ON YOUR LEFT WHILE LOOKING FWD FROM BACK OF TV.BUT DO CARE ABOUT RED, HV THICK WIRE. DONOT REMOVE IT FROM BOARD SIDE, U CAN REMOVE F RED WIRE FROM D BOARD SIDE. I REPEAT GET SOME HELP AND ASK HIM TO REPLACE ABOVE MENTIONED IC. ITS PRICE IS 11 US DOLLARS.BY THE WAY WHAT IS YR LOCATION , ARINC429

Thanks for your advise.  Im based in london.  Do you anywhere i can get pics from of the board parts ect??

I am in Dubai, I asked the location because I have one spare IC. It is my firm belive this IC is also bad in your case, even any Sony dealership/service centre knows about that as it is known issue to them. pls get this IC and ask some electrician to soler it. Photo will not help much for location.Once u remove the D board,which is on yr left looking from back of TV.

arinc429@hotmail.com

 

I have a series of blinking codes appearing on my Sony Triniron screen. The picture is still working in the background and the sound is not effected, it still funtions normally. One of the codes reads: 00898288 (EFE8), another is: 00893328 (EEEE) Any idea what these codes mean?

Thanks,

JLP

They blink continually every three seconds in a black rectangular box that covers the bottom half of the TV screen.

arinc429 said:

Rags said:

arinc429 said:

Rags said: My tv is Red 10 blinking, with audio but no picture. On the random occasion i might get the screen working, with the 10 red blinks still on. i must confess i have pulled the board out from behind, and i know noting. Its a Sony KP-FX423M91. i have also pulled a wire out and put it back in, and it started a couple times. Random wires, now i dont though. Scared incase it blows or something. Can you help a person in distress??

PLS GET SOME HELP FROM SOME ONE WHO CAN AT LEAST SOLDER AN IC.IF YOUR TV IS STILL ON 10 BLINKS AND SOME TIME U HAVE VIDEO ALSO ESPECIALLY U KEEP THE TV OFF FOR MORE THAN 10 HOURS.REPLACE THE IC 8002,  IC Part No. MCZ3001DB in D BOARD. IN YOUR TV D BOARD IS ON YOUR LEFT WHILE LOOKING FWD FROM BACK OF TV.BUT DO CARE ABOUT RED, HV THICK WIRE. DONOT REMOVE IT FROM BOARD SIDE, U CAN REMOVE F RED WIRE FROM D BOARD SIDE. I REPEAT GET SOME HELP AND ASK HIM TO REPLACE ABOVE MENTIONED IC. ITS PRICE IS 11 US DOLLARS.BY THE WAY WHAT IS YR LOCATION , ARINC429

Thanks for your advise.  Im based in london.  Do you anywhere i can get pics from of the board parts ect??

I am in Dubai, I asked the location because I have one spare IC. It is my firm belive this IC is also bad in your case, even any Sony dealership/service centre knows about that as it is known issue to them. pls get this IC and ask some electrician to soler it. Photo will not help much for location.Once u remove the D board,which is on yr left looking from back of TV. arinc429@hotmail.com

Thanks for the offer.  I was in dubai just 4 weeks ago.  I also bought the tv from there, jumbo electronics i think, they said transformer.  does the Ic have a roduct code .

Cheers

Have a sony projector i my workshop, FX432M91, comes ON, green light flashes and then Red light start blinking 4 times intervals, have checked every thing seems fine but the LINE OUTPUT STAGE is not switching ON, MY SUPPLY IS 135V,feeding into a mosfet before reaching the collector of Horizontal transistor as 92v. The Horizontal stage is not switching ON, PLEASE HELP.

Need service manual for KP-51WS510.
Please, someone help me.

Need service manual for KP-51WS510.
Please, someone help.

look in the technicians corner under the resources tap on the home page.

I have a Sony Triniton SRS BBE and is doing the self diag with 9 blinks. Your Page says Replace D 6116 abd D 8301 on the G Board. How much will this part be cost? In addition I did the Display, Channel(usedup botton),5, volumne Minus, power but the diag screen did not come on do you have any suggestions?

read trough the nine blink thread here on techlore. there are part numbers as well as where to purchace the parts from, they are not that much retail about 10 bucks or so for both. it is all here on techlore.

I'm also having the problem where the power light is blinking red 6 times. I understand from an earlier thread that it may be a bad lamp driver board or a bad lamp. Is this something that a tech would have to come out and check to confirm. If so, any recommmendations on where to contact one?
I have a kdf-55xs955 tv.
Thanks

I have a sony kp-57ws500....the tv will turn itself off then the red light will flash 8 times. From what I can figure out it is a problem with the d-board...i want to know if it is something we can fix or if it needs to be shipped out or taken somewhere.

with the what? you have me in suspence here!

I have a Sony KV40XBR800. The TV does not switch on. When I try to turn it on, the TV just makes a sound as though it is turning on but then suddenly it just switches off. The error message is 7 blinks. Sometimes the TV will turn on after 2 to 3 days of trying. Is this problem worth repairing? What would be the estimated cost? Thanks for your help.

HELLO GUYS I HAVE A SONY KV32TS36 THE HIGH VOLTAGE GOES UP AND DOWN CONSTANTLY LIKE PULSATING UP AND DOWN AS LONG AS THE TV IS PLUGGED IN ANY IDEAS WOULD BE
APPRECIATED.

THANKS ROB

I have a sony kp-46wt510 that is showing eight blinking lights...i see what I am suppose to look to troubleshoot this...does anyone have a repair manual they can send me?

Pages

 

Connect With Techlore