Lamp issue with 62525

7 posts / 0 new

Fri, 02/06/2009 - 09:16

thesuffering

I originally began my repairs starting with the blinking green light issue. Replaced the 4 caps on the dm board, now the tv acts like it wants to start sits for about 2 minutes then the red lamp light comes on like thebulb is bad. Looking in there the lamp doesn't look like it's turning on. Put a brand new bulb in there, have the same problem. Where should I be looking next?

Fri, 02/06/2009 - 21:33

Permalink

cuda

try reading the fault codes,

try reading the fault codes, may lead you in the correct direction.

Sat, 02/07/2009 - 08:14

Permalink

slinteriors

If the lamp led lights solid

If the lamp led lights solid red . Press menu and device/input buttons both in on the front panel together and hold for 5 seconds to see if the set will blink a two digit code such as a 3 and a 4 indcating 34 error. If you get a 34 error for instance ( Lamp Abnormality ) thats usually related to the power pwb capacitors that will need replacement. Other error codes can point in other directions such as a fan being out, lamp door or vent cover and etc,

Sun, 02/08/2009 - 01:11

Permalink

thesuffering

slinteriors said:

slinteriors said:
If the lamp led lights solid red . Press menu and device/input buttons both in on the front panel together and hold for 5 seconds to see if the set will blink a two digit code such as a 3 and a 4 indcating 34 error. If you get a 34 error for instance ( Lamp Abnormality ) thats usually related to the power pwb capacitors that will need replacement. Other error codes can point in other directions such as a fan being out, lamp door or vent cover and etc,

got error code 34, so the power pwb is the board is the one perpendicular to the dm module correct? I did find a tutorial online that said to replace the two 3300uF 10v caps, so i already did that, nothing so far. on that board there are 4 1000uF 16v caps that seem to be bulging a bit, think i should replace those? any other boards i should be looking at?

Sun, 02/08/2009 - 01:17

Permalink

slinteriors

yes the two 3300uf caps , the

yes the two 3300uf caps , the two 2200uf caps and the four 1000uf caps all need to be replaced the board location numbers are. use these volt ratings if you can.
C9A52 1000uF 16V
C9A59 1000uF 16V
C9A61 1000uF 16V
C9A62 1000uF 16V
C9A39 2200uF 35V
C9A40 2200uF 35V
C9A37 3300uF 16V
C9A38 3300uF 16V

Sun, 02/08/2009 - 01:18

Permalink

slinteriors

all the boards have issues

all the boards have issues with failing caps but the 34 error should be fixed by replacing the caps listed above

Mon, 02/09/2009 - 03:50

Permalink

thesuffering

slinteriors said:

slinteriors said:
yes the two 3300uf caps , the two 2200uf caps and the four 1000uf caps all need to be replaced the board location numbers are. use these volt ratings if you can.
C9A52 1000uF 16V
C9A59 1000uF 16V
C9A61 1000uF 16V
C9A62 1000uF 16V
C9A39 2200uF 35V
C9A40 2200uF 35V
C9A37 3300uF 16V
C9A38 3300uF 16V