My projection screen basically sook like a ribbon all the colors are fine i just replaced the main board because the convergence went bad and it has looked like this since can anyone shed some light
Can you be a little bit more specific please. Is this a secondary problem your having after you replaced the board? If it is, most likely you forgot to plug in a connector or plug, or the board you replaced is bad.
This is a new problem I pulled this out of another tv that was fine but the body was damaged it worked perfect it there the problem i had before was that the whole tv would not even turn on just flashed the code that the convergance ic were bad
You need to change the fuses or the pico fuses in the power supply that controls the plus and minus convergence control voltages.They will pop when the convergence IC's go bad in this model of TV set.
First locate the small coils in the main power supply. They are labeled L826 and L827. Check with a multimeter for plus 20 volts DC and minus 20 volts DC. Of course one coil will have the plus voltage, the other coil will have the minus voltage. Do you know how to read and follow circuit flow with a schematic diagram? If so, i will send you a copy of the service manual. If you do not, the service manual will not help you, as it does not give troubleshooting tips. The manufacturer assumes you already know how to troubleshoot solid state electronics. Sorry man, I'm afraid that if you do not know where to check, this is not a job for you to attempt.
I can with the service manual I took electronics for two years and have a good friend that did that stuff in for a while and he can help my email is [email protected] if you can send it
Larry Dillon said: First locate the small coils in the main power supply. They are labeled L826 and L827. Check with a multimeter for plus 20 volts DC and minus 20 volts DC. Of course one coil will have the plus voltage, the other coil will have the minus voltage. Do you know how to read and follow circuit flow with a schematic diagram? If so, i will send you a copy of the service manual. If you do not, the service manual will not help you, as it does not give troubleshooting tips. The manufacturer assumes you already know how to troubleshoot solid state electronics. Sorry man, I'm afraid that if you do not know where to check, this is not a job for you to attempt.
Is there anyway I could bother you for the service manual. I am going to attempt to replace the ICs in my set this weekend as the convergence went out yesterday. My email address is [email protected].
If you could actually send it to my Gmail account that would be better. My local ISP blocks alot of email that I actually want. Email is [email protected]. Thanks in advance!!
and look at the first picture, they are the 4 white connectors in the middle of the picture. Any help would greatly be appreciated. I am taking the board to a friend on Tuesday to have him solder the new IC Chips in for me but am currently stuck.
i would really appreciate it if i could get that manual e-mailed to me. i have a convergence issue. screen is kind of dark and it looks like watching 3-d without the glasses.
i would really appreciate a copy of that manual. my panny pt-53wx42f has convergence issues. it looks like a 3-d movie wthout the glasses. the screen is kind of dark, also.
I have that manual on my desktop computer that crashed a few months back. I have been meaning to get it back up and running but bought a new laptop and have been using it instead. I will see if I can at least get the pdf off the hard drive and email to those that need it. It is a very large file and might have to ftp it or something but give me a day or two and I will see what I can do.
contrerasjoe said: I have that manual on my desktop computer that crashed a few months back. I have been meaning to get it back up and running but bought a new laptop and have been using it instead. I will see if I can at least get the pdf off the hard drive and email to those that need it. It is a very large file and might have to ftp it or something but give me a day or two and I will see what I can do.
Thank you Joe. It'll be great if you get back the file.
I have found the manual on my old hard drive. It is a very large file (29MB). I could email it but anyone that needs it would have to know for sure if their email server will allow such a large file. Or if someone knows of a better way to make it available let me know.
I think he meant you send it .com, I created an account there and sent it to your email address. If you don't get it in your email account go to you send it .com (no spaces of course) and create a free account and I should be able to get it to you there.
contrerasjoe said: I think he meant you send it .com, I created an account there and sent it to your email address. If you don't get it in your email account go to you send it .com (no spaces of course) and create a free account and I should be able to get it to you there.
Hi
Thank you, I used the link you emailed me and I downloaded the file.
If anyone else wants the manual let me know.
By the way be very careful when making adjustments. I was in mine this morning trying to tweak some things and I accidently hit the wrong button and did a "Copy from D480p to 480P (i think) and now my TV's covergence is off and I can't get it to come back at all. If anyone has any ideas let me know. The screen now looks like a bowtie with all the colors off. Not sure if there is a reset or a setting to change it back.
contrerasjoe said: I have found the manual on my old hard drive. It is a very large file (29MB). I could email it but anyone that needs it would have to know for sure if their email server will allow such a large file. Or if someone knows of a better way to make it available let me know.
i really appreciate it. if you could send it to my e-mail @[email protected] it shouldn`t be a problem.
I have found the manual on my old hard drive. It is a very large file (29MB). I could email it but anyone that needs it would have to know for sure if their email server will allow such a large file. Or if someone knows of a better way to make it available let me know.
Can you be a little bit more specific please. Is this a secondary problem your having after you replaced the board? If it is, most likely you forgot to plug in a connector or plug, or the board you replaced is bad.
This is a new problem I pulled this out of another tv that was fine but the body was damaged it worked perfect it there the problem i had before was that the whole tv would not even turn on just flashed the code that the convergance ic were bad
You need to change the fuses or the pico fuses in the power supply that controls the plus and minus convergence control voltages.They will pop when the convergence IC's go bad in this model of TV set.
where are these located in this model i only see one fuse
where are these located in this model i only see one fuse
First locate the small coils in the main power supply. They are labeled L826 and L827. Check with a multimeter for plus 20 volts DC and minus 20 volts DC. Of course one coil will have the plus voltage, the other coil will have the minus voltage. Do you know how to read and follow circuit flow with a schematic diagram? If so, i will send you a copy of the service manual. If you do not, the service manual will not help you, as it does not give troubleshooting tips. The manufacturer assumes you already know how to troubleshoot solid state electronics. Sorry man, I'm afraid that if you do not know where to check, this is not a job for you to attempt.
I can with the service manual I took electronics for two years and have a good friend that did that stuff in for a while and he can help my email is [email protected] if you can send it
Is there anyway I could bother you for the service manual. I am going to attempt to replace the ICs in my set this weekend as the convergence went out yesterday. My email address is [email protected].
The Panasonic PT-53WX42F
If you could actually send it to my Gmail account that would be better. My local ISP blocks alot of email that I actually want. Email is [email protected]. Thanks in advance!!
Joe, I will send you out the service manual. It is not the exact model number but the cuircuit is the same. Good Luck with your repair.
Can anyone here tell me how to disconnect the 4 white connectors that connect the convergence board to the board beside it. If you go to this site
http://cmpalmer.blogspot.com/2006_11_01_archive.html
and look at the first picture, they are the 4 white connectors in the middle of the picture. Any help would greatly be appreciated. I am taking the board to a friend on Tuesday to have him solder the new IC Chips in for me but am currently stuck.
One side clips up from the other. If you look at the right side where there is like a tab, that is the side that unclips and folds upwards.
Thanks Larry, I was able to get the board out and hopefully will get my TV back up and working by Tuesday. Your help has been greatly appreciated.
Hey,
I really need the service manual for the pt-53wx42f. i am replacing the converg amps and will need to access the service menu...
a pdf at [email protected] will be much appreciated.
my screen has gone crazy with little blue lines. my thought is to just replace the IC's. can any one help with the parts # on them. thanks
i would really appreciate it if i could get that manual e-mailed to me. i have a convergence issue. screen is kind of dark and it looks like watching 3-d without the glasses.
i would really appreciate a copy of that manual. my panny pt-53wx42f has convergence issues. it looks like a 3-d movie wthout the glasses. the screen is kind of dark, also.
I need the service manual for the pt-53wx42f.
a pdf at [email protected] would be appreciated.
Hi
I really need the service manual for pt-53wx42f model.
If LarryDion can email me the pdf file to ablabid[at]hotmail.com; I will appreciate.
thank you
I have that manual on my desktop computer that crashed a few months back. I have been meaning to get it back up and running but bought a new laptop and have been using it instead. I will see if I can at least get the pdf off the hard drive and email to those that need it. It is a very large file and might have to ftp it or something but give me a day or two and I will see what I can do.
Thank you Joe. It'll be great if you get back the file.
Il'll be wainting for news.
I have found the manual on my old hard drive. It is a very large file (29MB). I could email it but anyone that needs it would have to know for sure if their email server will allow such a large file. Or if someone knows of a better way to make it available let me know.
find send it.com and send me a link please.
Hi;
I don't understand what does this mean.
I find the site "sendit.com", but it contains nothing about downloading any service manual.
I think he meant you send it .com, I created an account there and sent it to your email address. If you don't get it in your email account go to you send it .com (no spaces of course) and create a free account and I should be able to get it to you there.
Hi
Thank you, I used the link you emailed me and I downloaded the file.
One more time, thanks.
Edir
If anyone else wants the manual let me know.
By the way be very careful when making adjustments. I was in mine this morning trying to tweak some things and I accidently hit the wrong button and did a "Copy from D480p to 480P (i think) and now my TV's covergence is off and I can't get it to come back at all. If anyone has any ideas let me know. The screen now looks like a bowtie with all the colors off. Not sure if there is a reset or a setting to change it back.
i really appreciate it. if you could send it to my e-mail @[email protected] it shouldn`t be a problem.
I have found the manual on my old hard drive. It is a very large file (29MB). I could email it but anyone that needs it would have to know for sure if their email server will allow such a large file. Or if someone knows of a better way to make it available let me know.
Pages